Expert Pool Equipment Repair — Pumps, Filters & Chlorinators

Fast, Reliable Pool Equipment Repairs Across Perth

When your pool equipment stops working, it does not take long for problems to develop. A failed pump means no filtration or circulation. A broken chlorinator means no sanitisation. Within just a few days of equipment failure, your pool water can deteriorate rapidly — especially during Perth’s hot summer months when temperatures consistently exceed 35 degrees Celsius.

Our equipment repair service is designed to get your pool back up and running as quickly as possible. We carry common replacement parts on our service vehicles, which means many repairs can be completed during a single visit. For less common parts, we source them quickly through our supplier network and return to complete the repair promptly.

Pool Pump Repairs

The pool pump is the heart of your pool’s circulation system. When it fails, everything downstream stops working — your filter, chlorinator, and heating system all rely on the pump to move water through the system.

Common Pump Problems We Fix

Mechanical seal failure is the most frequent pump issue we encounter. The mechanical seal prevents water from entering the motor housing. When it wears out, you will notice water dripping from the base of the pump. Left unaddressed, water will reach the motor bearings and cause a far more expensive failure. A seal replacement typically costs a fraction of a new pump and takes about an hour.

Capacitor failure causes the pump to hum but not start, or to start sluggishly. This is an electrical component that provides the initial surge of power to get the motor spinning. Replacement is straightforward and inexpensive.

Impeller blockage or damage reduces water flow and puts strain on the motor. Debris such as small stones, hair pins, or broken cleaner parts can lodge in the impeller. We disassemble the wet end of the pump to clear blockages and inspect the impeller for wear.

Motor bearing failure produces a loud grinding or screeching noise. If caught early, the bearings can be replaced. If left too long, the motor shaft and housing may be damaged beyond repair.

Filter Repairs and Service

Sand Filters

Sand filters are the most common filter type in Perth pools. Over time, the sand media becomes compacted and channelled, reducing its ability to trap fine particles. We replace filter sand — typically every five to seven years — and inspect the laterals, standpipe, and multiport valve during the process.

Multiport valve issues are another common problem. Leaking between ports, a stiff handle, or water running to waste can all indicate a worn spider gasket or cracked valve body. We carry replacement gaskets for the most popular valve models.

Cartridge Filters

Cartridge filters require regular cleaning and periodic cartridge replacement. We can deep clean cartridges using a chemical soak to extend their life, and we stock replacement cartridges for common filter models.

Chlorinator Repairs

Salt chlorinators are the standard sanitisation system in Perth pools. The chlorinator cell — the component that converts salt into chlorine — has a finite lifespan, typically three to five years depending on the model and how well the water chemistry has been maintained.

Common Chlorinator Issues

Low chlorine output despite the cell running is often caused by calcium buildup on the cell plates. We remove the cell and perform a chemical clean to restore output. Regular cleaning extends cell life significantly.

Cell failure — when the cell stops producing chlorine entirely — usually means the cell has reached the end of its life. We supply and install replacement cells for all major brands including Zodiac, Astral Pool, Davey, Pentair, and Hayward.

Control board faults can cause error codes, failure to detect the cell, or the system not powering on. We diagnose control board issues and can often repair them, though in some cases a replacement board is required.

Pricing for Equipment Repairs

Our callout fee starts from $150, which covers the diagnostic assessment, travel to your property, and labour for straightforward repairs. Parts are charged separately at competitive rates, and we always provide a clear quote before proceeding with any work.

For major repairs or equipment replacements, we provide written quotes so you can make an informed decision. We will always tell you honestly whether a repair or replacement is the better investment for your situation.

Serving All Perth Suburbs

We provide pool equipment repair services across the entire Perth metropolitan area, including Mount Claremont, Nedlands, Subiaco, Cottesloe, Scarborough, Joondalup, Fremantle, Canning Vale, and everywhere in between. Our service vehicles are based in Mount Claremont, which means fast response times for the western suburbs.

If your pool equipment has stopped working or is not performing as it should, contact us today. We will diagnose the problem quickly and get your pool back to normal with minimum downtime.